Photo by eberhard grossgasteiger on Pexels
You go to check the laundry or the side of the house and find a puddle under the hot water system. Maybe it is a slow drip, maybe it is a steady stream. Either way, the first question is the same: is this a quick fix, or does the whole system need to come out?
The honest answer is that it depends on where the water is actually coming from. Water pooling at the bottom of a hot water system can originate from a handful of places, and some are minor and inexpensive to fix while others mean the tank has reached the end of its life.
This guide helps you work out what is leaking, what to do right now to limit the damage, how to tell a repairable leak from a failed tank, and how to decide between repair and replacement.
What to Do Right Away
Before you diagnose anything, make the situation safe.
- Turn off the power or gas. For an electric system, switch off the isolator or circuit breaker. For gas, turn off the gas supply at the unit or bottle. Do this before the water level in the tank drops, because an electric element running without water can burn out.
- Turn off the cold water supply to the unit using the isolation valve on the inlet pipe. If you cannot find it, turn off the water at the main. Our guide on locating your shut-off valve can help.
- Do not touch the water if it is near electrical connections. Hot water can scald, and water near wiring is dangerous.
- Contain the water with towels or buckets. Our guide to collecting water in a plumbing emergency has practical tips.
- Take photos of the leak and the unit's compliance plate, which shows the model, serial number and manufacture date. This is useful for warranty and insurance.
Where Is the Water Actually Coming From?
Pooling at the bottom does not always mean the bottom of the tank is leaking. Water runs down and collects. Dry the unit and watch carefully to find the true source.
1. The TPR Valve or Its Drain Pipe
The temperature and pressure relief (TPR) valve is a safety device that releases water if pressure or temperature gets too high. It has a discharge pipe that runs down the side of the tank.
- A small amount of dripping, particularly while the unit is heating, can be normal.
- A constant or heavy flow suggests a faulty valve or excess pressure.
Our guide to what a TPR valve is explains what is normal and what is not. Replacing a faulty TPR valve is typically a straightforward repair.
2. High Water Pressure
If your mains pressure is too high, it can force water out of the TPR valve and strain fittings and the tank. A pressure limiting valve may be needed. Read about pressure limiting valves and the effects of high water pressure.
3. Loose or Failing Pipe Connections and Fittings
Inlet and outlet pipes, unions, isolation valves and tempering valves can all leak from worn seals or loose connections. Water often runs down the pipe and drips from the base, which makes it look like a tank leak. These are usually repairable.
4. Condensation
Cold water in a hot or humid environment can cause condensation on pipes and the tank, which then drips. It is usually minor and goes away when the weather changes. It is not a tank failure.
5. Heat Pump or Solar System Drain
Heat pumps produce condensate that drains from a dedicated outlet. Solar systems have overflow and relief pipes. Water from these outlets can be normal, but check with your installer if the volume seems high.
6. A Leaking Tank (Corrosion or Failure)
If the water is coming from the tank body, seams or the base itself, the steel inner tank has corroded through. This is the leak that means replacement.
7. A Failed Heating Element Gasket (Electric Systems)
Some electric systems have a flange where the element is mounted. A worn gasket can leak. This is occasionally repairable, but on an older unit it often accompanies a corroded tank.
How to Tell Whether It's the Tank
Try these safe checks once the power and water are off and the unit is cool:
- Dry everything, then look for the point where water first reappears. Water that emerges from the tank's outer casing, bottom or seams points to the tank itself.
- Check the pipes and valves above the tank for drips running down.
- Look at the TPR discharge pipe. Is water coming from it?
- Look for rust or staining on the tank base, around the fittings, or on the floor below.
- Listen for hissing or dripping inside the casing.
- Consider the age. See below.
If you cannot identify the source, a plumber can find it quickly.
Repair or Replace? How to Decide
| Situation | Usual answer |
|---|---|
| Leak from the TPR valve or discharge pipe | Repair or replace the valve, and check the pressure |
| Leak from a pipe connection, isolation valve or tempering valve | Repair |
| Leak from an element flange gasket on a newer unit | Often repairable |
| Leak from the tank body, seams or base | Replace |
| Leak from an old unit with widespread rust | Replace |
| Repeated repairs on an ageing system | Usually replace |
| Unit within warranty and leaking from the tank | Contact the manufacturer or installer about a warranty claim |
Consider the Age of the System
A tank leak almost always means the end of the system, and age gives context. Electric and gas storage tanks commonly last somewhere around 8 to 12 years (some sources say up to 15), depending on the type, water quality and maintenance, although coastal conditions and hard water can shorten that. See our guide to how long a hot water system should last on the Gold Coast and the signs your hot water system needs replacing.
Think About Efficiency and Options
If you do need to replace, it is a chance to choose a system that suits your household better. Options include electric storage, gas storage, gas continuous flow, solar and heat pump. Our guides on tankless vs tank, heat pump systems, solar systems and sizing a system can help you decide.
Check the Warranty
Many hot water tanks have a multi-year warranty on the cylinder. If yours is within it, contact the manufacturer or installer before arranging any work, and keep the compliance plate details and proof of purchase to hand. Warranty terms vary, so read yours.
Signs the Leak Is Serious
- Water flowing continuously from the tank
- Rust-coloured water from the hot taps
- A rusted tank base or casing
- Hissing, popping or banging noises. See our guide on water heater noises
- A damp or stained floor or wall around the unit
- Mould or a musty smell near the system
- A rising water bill. See why your water bill might be high
Why You Should Not Delay
A leaking hot water system can cause:
- Water damage to floors, walls and cabinetry
- Mould and rot in damp conditions
- Electrical hazards around electric units
- Wasted water and energy
- A sudden loss of hot water when the tank empties
- Higher repair costs if the leak spreads or damages surrounding structures
If you have switched off the system, you will be without hot water, so book a plumber promptly.
When to Call a Licensed Plumber
Call a plumber or gas fitter if:
- You cannot find where the water is coming from
- The leak is from the tank
- The TPR valve is constantly discharging
- You smell gas, or see scorch marks or sparking
- The system is old or has a history of problems
- You need to replace parts or the whole system
Hot water systems involve electricity, gas and pressurised hot water, and in Queensland the work must be done by licensed professionals.
How to Reduce the Chance of Leaks
- Service the system regularly. See our hot water maintenance tips.
- Test the TPR valve as recommended in your manual.
- Flush sediment from the tank when appropriate. Our guide to removing sediment explains how.
- Check the pressure in your home. Use our guide to testing water pressure.
- Check the anode and the unit's condition during service visits.
- Inspect the area around the system every few months for drips and rust.
- Replace proactively when the system is old and showing signs of failure.
Frequently Asked Questions
Is it normal for a hot water system to drip?
A small amount of dripping from the TPR valve discharge pipe while the unit is heating can be normal. A constant drip, or water from anywhere else, is not.
Can a leaking hot water tank be repaired?
If the leak is in the tank body, no. The inner tank cannot be patched reliably. Leaks from valves, fittings or the TPR valve can usually be repaired.
Is a leaking hot water system dangerous?
It can be. The risks include scalding, electric shock around electric units, gas safety issues, and water damage. Turn off power or gas and water, and call a plumber.
How quickly do I need to fix it?
As soon as possible. Leaks tend to get worse, and a tank leak can empty quickly.
Will my insurance cover a leaking hot water system?
It depends on the policy and the cause. Policies often cover sudden damage but not wear and tear. Check your policy and keep photos and records.
What should I do while waiting for the plumber?
Keep the power or gas and water off, contain the water, avoid using the system, and photograph the leak and the compliance plate.
Final Thoughts
A hot water system leaking from the bottom is a sign to act, but not always a reason to panic. If the source is a valve or fitting, a repair may fix it. If it is the tank itself, replacement is the only reliable answer. Making the system safe first, finding the source, and checking the age and warranty will tell you which way to go.
Coastal Plumbing Professionals repairs and replaces hot water systems across the Gold Coast, and can usually get you back to hot showers fast. Call 1300 590 085 or visit our hot water repair and installation page to book.
Resources
- Plumbing and drainage | Queensland Building and Construction Commission
- AS/NZS 3500.4 Heated Water Services | Standards Australia
- Gasfitting licences | Queensland Building and Construction Commission
- Energy Rating: Water Heaters
- Electrical Safety Office Queensland