Photo by Alexas Fotos on Pexels
Your hot water system stores water at a temperature hot enough to cause a serious scald in a matter of seconds. Yet you step into the shower each morning and the water is comfortably warm. The reason it does not burn you is a small brass fitting, usually tucked near the hot water system, that most homeowners have never heard of: the tempering valve.
Understanding what it does and why it matters helps you keep your family safe, spot problems early, and avoid confusing it with other valves around your hot water system.
This guide explains what a tempering valve is, how it works, why storing water hot is actually a safety requirement, what Queensland's rules generally expect, the signs of a failing valve, and what to do about it.
What Is a Tempering Valve?
A tempering valve (sometimes called a thermostatic mixing valve or tempering device) blends hot water from your hot water system with cold water before it flows to your bathroom fixtures. The result is water at a safe, controlled temperature, regardless of how hot the stored water is.
It is typically installed on the hot water outlet pipe near the heater, and it supplies the bathrooms, and sometimes other fixtures, with water that has been lowered to a safe maximum.
Why Hot Water Is Stored So Hot
It seems odd to store water at a scalding temperature and then mix it down. There is a good reason. Storage tanks are generally kept at 60°C or higher because:
- It prevents the growth of harmful bacteria, including Legionella. These bacteria can grow in warm water, and they are a health risk if inhaled in a fine mist, such as from a shower. Storing water at a high temperature kills them and stops them multiplying.
- It increases the usable volume of hot water. Hot water mixed with cold at the tap stretches the supply, so a smaller tank goes further.
The trade-off is that 60°C water can cause a severe scald very quickly, which is why it must be reduced before it reaches the outlets people use for washing.
How Hot Is Too Hot?
Scald risk depends on temperature and time. Water at 60°C can cause a full-thickness burn in a matter of seconds, and children, older people and people with reduced sensation are at even higher risk. At 50°C, the time to cause serious injury is considerably longer, which is why this temperature is commonly used as the maximum for water delivered to people's bodies.
What Do the Rules Say?
In Queensland, the plumbing code requires hot water delivered to fixtures used for personal hygiene, such as showers, baths and basins, to be limited to a maximum of 50°C. A tempering valve is the standard way of achieving this, although a water heater preset to deliver at 50°C can also meet the requirement. Some high-risk settings, such as certain facilities for young children or the elderly, have a lower limit of 45°C. Queensland treats a like-for-like replacement of a hot water system as a new installation for this purpose. The requirements are set out in the Queensland Plumbing and Wastewater Code and in AS/NZS 3500.4, and they apply to new installations and when hot water systems are replaced. Exact requirements can vary by building type and age, so your licensed plumber can confirm what applies to your property.
Tempering valves must be installed by a licensed plumber, and must use compliant, WaterMark-certified products.
Tempering Valve vs TPR Valve: What's the Difference?
People often confuse these two, as both are valves on or near the hot water system. They do very different jobs.
| Tempering valve | TPR valve | |
|---|---|---|
| What it does | Mixes hot and cold water to lower the outlet temperature | Releases water if pressure or temperature inside the tank becomes unsafe |
| What it protects against | Scalding at taps and showers | Tank rupture or explosion |
| Where it is | On the hot water outlet pipe, near the heater | On the tank itself, with a discharge pipe |
| Operates | Continuously, whenever hot water is used | Only in an over-pressure or over-temperature situation |
Read more about the safety valve in our guide to what a TPR valve is.
How a Tempering Valve Works
Inside the valve is a temperature-sensitive element, often a wax or bimetallic component, that expands and contracts with temperature. As hot water enters, the element adjusts how much cold water is allowed to mix in, aiming to keep the outlet temperature steady at the set point.
Many valves have an adjustable setting, typically factory-set or adjusted by the installer. They are designed to cope with changes in supply temperature and flow, although they are not perfect, and pressure imbalances between the hot and cold supplies can affect their performance.
Signs Your Tempering Valve Is Failing
Tempering valves contain moving parts and are exposed to hot water and mineral deposits, so they can wear out or become blocked.
- Water is too hot at the shower or tap. This is a safety concern and needs attention promptly.
- Water temperature fluctuates between hot and cold during use.
- Water is not hot enough, even though the tank is fine.
- Reduced hot water flow or pressure at bathroom fixtures. See also our guide on hot water pressure problems.
- Hot water takes a long time to arrive or runs out unusually fast.
- Noises such as banging or humming in the pipes near the valve.
- Visible leaks, corrosion or scale on or around the valve.
- The valve is old. There is no fixed lifespan, but valves in hard water areas or ones that have never been serviced tend to wear sooner.
If the water at the tap is scalding, stop using the hot tap and have it checked immediately. Children, older people and anyone with limited sensation are particularly at risk.
What Causes Tempering Valves to Fail?
- Mineral and scale build-up inside the valve, particularly in hard water areas
- Sediment from the hot water system
- Age and wear of the internal parts
- Pressure imbalance between hot and cold supplies
- Debris blocking the inlet screens
- Incorrect installation or adjustment
- Corrosion, especially in coastal conditions. See our guide to corrosion-resistant fixtures for coastal homes
Can You Adjust or Replace It Yourself?
Adjusting or replacing a tempering valve changes the temperature of the water delivered to your family, and getting it wrong can lead to scalding or, if the stored water is not hot enough, bacterial growth. Because the valve is a regulated safety device installed on a hot water system, in Queensland the work needs to be done by a licensed plumber, with compliant parts and a proper test of the outlet temperature.
What you can do yourself:
- Check the water temperature at the tap occasionally. A thermometer helps.
- Look for visible leaks or corrosion around the valve.
- Make a note of the valve's location so you can point it out to your plumber.
What a Plumber Will Do
- Check the outlet temperature at the fixtures.
- Inspect the valve for scale, leaks, damage and correct installation.
- Test its operation, including how it responds to changes in flow and temperature.
- Clean, service or replace the valve as needed.
- Check the hot water system itself, including the stored temperature, TPR valve and pressure. See our guides on maintaining your hot water system and removing sediment.
- Set the valve correctly and confirm the delivered temperature is safe.
How to Keep Your Tempering Valve Working
- Have your hot water system serviced regularly, and ask for the tempering valve to be checked
- Flush sediment from the tank as recommended
- Keep an eye on water pressure. High pressure can strain fittings. See our guide to pressure limiting valves
- Do not turn your hot water thermostat down below the recommended storage temperature in an attempt to be safer, because it can allow bacteria to grow
- Replace the valve if it is old or showing signs of failure
- Replace the whole system proactively as it ages. See signs your hot water system needs replacing
Frequently Asked Questions
Do I need a tempering valve?
If you have a storage hot water system in Queensland, you generally need one so water delivered to bathrooms does not exceed 50°C. Your licensed plumber can confirm what applies to your home.
Can I turn my hot water down instead of using a tempering valve?
You should not. Storing water below about 60°C can allow Legionella and other bacteria to grow. The safe approach is to store it hot and mix it down at the outlet.
Why is my shower water suddenly too hot?
The tempering valve may have failed or be blocked. Stop using the hot tap, and get it checked straight away.
How long does a tempering valve last?
It varies with water quality, use and maintenance. Trade guidance commonly puts it at around 5 to 8 years, and valves in hard water areas can wear sooner. A plumber can check yours during a hot water service.
Do instantaneous (continuous flow) systems need a tempering valve?
Instantaneous systems heat water on demand and often deliver to a set temperature, so they may not need one in the same way. Requirements depend on the model and installation, so check with your plumber.
Where is my tempering valve?
It is usually on the hot water outlet pipe close to the hot water system. If you cannot find it, a plumber can show you.
Final Thoughts
A tempering valve is one of the most important safety devices in your home, and one of the least noticed. It lets your hot water system store water hot enough to stay free of bacteria, while keeping the water at your taps from scalding anyone. If your water has become too hot, too cold, or inconsistent, do not ignore it.
Coastal Plumbing Professionals tests, services and replaces tempering valves and hot water systems across the Gold Coast. Call 1300 590 085 or visit our hot water repair and installation page to book a check.
Resources
- Queensland Plumbing and Wastewater Code | Queensland Government
- AS/NZS 3500.4 Heated Water Services | Standards Australia
- Legionella, legionellosis and Legionnaires' disease | Queensland Health
- Scalds prevention | Kidsafe Australia
- Queensland Building and Construction Commission (QBCC)