Photo by HRIDYAKSH GEJWAL on Pexels
The Gold Coast gets plenty of rain, and most of it runs off your roof, down the gutters, and out through the stormwater drains. Catching some of it in a tank and using it for flushing toilets and washing clothes is one of the most practical ways to cut your mains water use. It also gives you a source of water for the garden when restrictions apply.
But a rainwater tank connected to your house is not just a tank and a hose. It is a second water supply that has to be plumbed in correctly so it never mixes with your drinking water, never runs dry without warning, and never causes problems for you or the public network.
This guide explains how rainwater tank plumbing works, what a typical connection to toilets and laundry involves, the safety and compliance rules to keep in mind, the equipment you need, and how to maintain the system.
Why Connect a Rainwater Tank to the House?
- Lower mains water use. Toilets and laundry use a large share of household water, and neither needs drinking-quality water.
- A water source during restrictions. Tank water can keep gardens and some household uses going.
- Reduced stormwater runoff. Tanks reduce the volume of water leaving your property in a storm.
- Resilience. An independent supply can help in a short supply interruption.
For a wider look at saving water at home, see our guide to water-saving fixtures.
What Can Rainwater Be Used For?
Common uses for tank water connected to the house include:
- Flushing toilets
- Cold water supply to the washing machine
- Garden watering and outdoor taps
- Washing cars and outdoor cleaning
Using rainwater for drinking or cooking is a separate matter. Roof-collected rainwater can carry contaminants such as bird droppings, dust and debris, and health authorities generally advise caution unless it is properly filtered and treated. In a mains-supplied area, most households keep drinking and cooking on the mains supply. If you are considering using tank water for drinking, speak to your plumber and refer to Queensland Health guidance.
How a Rainwater Tank Plumbing System Works
A typical setup includes:
- Catchment. Roof, gutters and downpipes collect the rain.
- First flush diverter and leaf filters. These keep the first, dirtiest water and debris out of the tank.
- The tank. Stores the water. It must be sealed and screened to keep out mosquitoes, animals and light.
- A pump. Draws water from the tank and delivers it to the house at usable pressure.
- Pipework to the fixtures. Dedicated pipes that run to the toilets, laundry and outdoor taps.
- A mains water top-up or switching system. Supplies backup water when the tank runs low, in a way that keeps the two supplies separated.
- Overflow. Directs excess water to the stormwater system when the tank is full.
The Most Important Rule: Keep the Two Supplies Separate
The biggest risk with rainwater plumbing is cross-connection, where rainwater and mains water could mix. If rainwater were to flow back into the mains supply, it could contaminate the drinking water of your household and potentially neighbours.
To prevent this, the plumbing code requires specific arrangements for the mains top-up. Common methods include:
- A compliant air gap, where a mains trickle top-up enters the tank above the maximum water level, with a physical gap between the inlet and the water, so back-siphoning is impossible. Queensland guidance indicates that a top-up with a compliant air gap may not need a separate backflow device
- An approved automatic switching device, which supplies mains water to the rainwater pipes only when the tank is low
- A backflow prevention device (such as a dual check valve with atmospheric port), where an internal top-up does not have a compliant air gap
Our guide to backflow prevention devices explains why this matters so much.
Marking and Identifying Rainwater Pipes
To avoid accidental cross-connections and misuse, pipework and outlets carrying non-drinking water must be clearly identified under the plumbing standards. This typically involves approved colours, labelling and signage, such as warning signs on taps that are not for drinking. Your licensed plumber will use the correct identification for your installation. Do not remove or alter these markings.
Connecting a Tank to Toilets
Plumbing a tank to your toilets usually involves:
- A dedicated rainwater supply line to each cistern
- A pump and pressure control to deliver water reliably
- A mains top-up arrangement so toilets still flush when the tank is empty
- Correct labelling at the cistern and on the pipes
Our toilet repairs and installation service can help with connecting cisterns. If you are replacing or upgrading, our guides on replacing a toilet cistern and choosing a new toilet are useful.
Connecting a Tank to the Laundry
A laundry connection typically supplies the cold side of the washing machine with rainwater. Points to consider:
- Hot water still comes from the hot water system, which is fed from the mains
- Water quality matters. Fine sediment can clog machine inlet filters. A filter at the tank outlet or before the machine helps
- Machine compatibility. Check your machine's manual about operating with rainwater and pressure requirements
- Hose condition. Rainwater lines add another connection point. Our guide to washing machine hoses explains why hoses need checking
See also our laundry plumbing setup guide.
Pumps and Pressure
A pump is needed to move tank water to the house. Key points:
- Pump type. Surface pumps sit on the ground near the tank. Submersible pumps sit inside it.
- Pressure control. Pressure switches or controllers manage flow so the pump does not run constantly.
- Run-dry protection. A pump that runs without water can burn out. Many pumps and switching devices include protection.
- Noise and location. Pumps can be noisy, so consider where it sits relative to bedrooms and neighbours.
- Power supply. Pumps must be wired by a licensed electrician.
Rules and Compliance in Queensland
Rainwater tank plumbing is regulated. In general:
- Connecting a tank to a house's plumbing is licensed plumbing work. It must be done by a licensed plumber using WaterMark-certified products.
- The installation must comply with the Queensland Plumbing and Wastewater Code and AS/NZS 3500, including the rules on cross-connection, backflow prevention and pipe identification.
- Tank openings should be screened with mosquito-proof mesh to stop breeding. Your plumber can confirm the screening requirements that apply.
- Overflow must discharge to a legal point, usually the stormwater system, and not onto neighbouring properties.
- Local planning rules may affect where a tank can be placed and its size. Check with the City of Gold Coast.
Requirements change, so confirm current rules for your property with your plumber and council.
Common Problems with Rainwater Plumbing
- Pump runs constantly or cycles on and off. Often a leak, a pressure switch problem or an air lock.
- Tank runs dry quickly. May indicate a leak, or demand that exceeds the catchment.
- Mains top-up not switching. A failed switching device or valve.
- Discoloured or smelly water. Debris, algae or sludge in the tank, or stagnant water.
- Low pressure at fixtures. Pump sizing, blocked filters or pipework restrictions.
- Mosquitoes in the tank. Damaged or missing screens.
- Overflowing tank. Blocked overflow or undersized stormwater connection.
Maintenance Checklist
- Clean gutters and leaf filters regularly. See our guide to overflowing gutters.
- Check the first flush diverter and empty it as needed.
- Inspect mosquito screens and repair any holes.
- Check the tank for sludge and arrange cleaning every few years.
- Check the pump, pressure switch and filters for signs of wear.
- Test the mains top-up by running the tank low if safe to do so, or ask your plumber to check it.
- Look for leaks along the pipework and at connections. The water meter test helps spot hidden leaks.
- Have a licensed plumber inspect the system periodically, and after storms or any changes to your plumbing.
When to Call a Licensed Plumber
- Before installing or connecting a tank
- If you notice any sign of rainwater mixing with mains water, such as discoloured water from drinking taps
- If the pump or switching device is faulty
- If pipework has been altered, or you are renovating
- If the system is noisy, leaking or not delivering pressure
- If you are unsure whether your existing installation is compliant
Frequently Asked Questions
Can I connect a rainwater tank to my toilet myself?
No. Connecting a tank to household plumbing is licensed work in Queensland, and cross-connection mistakes can contaminate your drinking water.
Is rainwater safe for the laundry?
Generally yes for cold water washing with appropriate filtration, but check your machine manual and keep the system maintained.
Do I need a mains top-up?
Most households do, so toilets and the laundry keep working in dry spells. The top-up must be installed with an air gap or approved device that prevents mixing.
Can I drink tank water?
Roof-collected rainwater can contain contaminants. If your property has mains supply, most people use the mains for drinking. Check with Queensland Health and your plumber before drinking tank water.
Why does my tank pump keep turning on?
A leak in the pipework, a faulty pressure switch, or a worn toilet cistern valve can all cause a pump to cycle. A plumber can trace it.
How much water will a tank save?
It depends on the tank size, roof area, rainfall and household use. A plumber can help you size a system for your home.
Final Thoughts
A rainwater tank connected to your toilets and laundry makes good use of the Gold Coast's rain, but only if the plumbing is right. Keeping the rainwater and mains supplies separate, using compliant equipment, and maintaining the system are what make it safe and reliable.
If you are planning a new tank, or you want an existing system checked, Coastal Plumbing Professionals can assess your setup and install or repair it to code. Call 1300 590 085 or contact us online to get started.
Resources
- Rainwater tanks | Queensland Government
- Rainwater tanks | Queensland Health
- AS/NZS 3500 Plumbing and Drainage | Standards Australia
- enHealth: Guidance on use of rainwater tanks | Australian Government
- City of Gold Coast: Water saving